Welding and Woodworking

Posts Tagged ‘cutting’

Circle Cutting

Friday, June 4th, 2010

Circle Cutting
Circle Cutting

How to Cut, Score and Break Glass

Glass can be cut into strips, geometric shapes, circles, ovals, curves and with a glass saw, almost any shape.

Some Things to Keep in Mind

• Warm glass (glass at room temperature) cuts easier than cold glass

• Work surface needs to be flat

• Score on the smooth side of glass rather than on the textured side

• Hold glass cutter in a vertical position as you would a pen or pencil

• Don’t use excessive pressure. Too deep of a score can result in a bad break

• For protection, it’s a good idea to wear glasses or another type of eye protection

Straight Cuts

When making a straight score, start scoring the glass from the point farthest from your body and pull the glass cutter towards you. Once a score line is made, use running pliers (if strip is at least 1” wide) by placing the running pliers centered on the score line and gently squeeze the handles. You will hear a slight cracking noise and see the glass separate along the score line. Or, hold the stained glass sheet over an edge of a table with the score line slightly overhanging the edge. Use breaking or grozier pliers and apply gentle pressure in a downward motion along the score line. This can also be done with your hands using the same downward motion. Practice will make for perfection, soon.

Curve Cuts

To make a curved cut, use the glass cutter to cut off sections one at a time. This allows you to work into the curve. Glass likes straight lines or lines with gentle bends. If the shape has irregularities or small projections, these are easily removed with a nipper or glass grinder. In other words, don’t rush the cut especially if it is an inside curve. Just chip away at it a little bit at a time.

Cutting Circles

Score the glass in the shape and size of the desired circle. Use a permanent marker to place a dot where you start scoring to avoid going over the starting point. Next, place the scored line side of the glass down on a piece of corrugated cardboard. Use light pressure and press along the score line until you see it run the circle. Then, turn the glass over to the side you first scored on and score several tangent cuts radiating out from the circle. Finally, break each tangent score line with breaking pliers. The circle should cut clean without any jagged edges.

How To Avoid Common Problems

• Cutter wheel wears out quickly – Lift your cutter up instead of sliding it off the edge of the glass or cut on a surface covered with vinyl or carpet

• Bad breaks after scoring – Too much pressure was applied on the glass cutter

• Score line looks like dotted line – Cutter wheel is dull and needs to be replaced

Be sure to turn your pattern template over when you are tracing your pattern onto the backside of the glass where it smoother. Failure to do this will end up in wasted glass and lots of wasted time, not to mention frustration.

About the Author

I started out as a stained glass admirer. After a class in stained glass, I became addicted. At first I made stained glass to decorate my home, which lead to friends asking me to make stained glass for them. Now I am a full time professional making stained glass as well as instructing others on how to make stained glass. My studio is located outside of Chicago, Illinois. For more information on making or buying stained glass, to find a free pattern or to sign up for my newsletter, go to http://www.creativity-in-glass.com

How do I cut a circle into 14 even pieces?

I have to cut a really big circle into 14 pieces using straight lines coming out of the middle (Like if you where to cut a pizza or a pie).

Here is a simples answer

1. Draw a circle and one radius.
2. by measuring 25.71 degrees angle draw a line from centre to circumference of circle i.e 2nd radius.
3. now using 2nd radius as base of protractor repeat the step to. Repeat till end. you end up in 14 equal sectors

DIY circle cutting jig for your router

NEW Nestabilities Cutting Die - Pinking Circles Small
NEW Nestabilities Cutting Die - Pinking Circles Small
Paypal   US $16.99
Nestabilities Cutting Die - Big Scalloped Circles Small
Nestabilities Cutting Die - Big Scalloped Circles Small
Paypal   US $16.99
Nestabilities Cutting Dies - Standard Circle Large
Nestabilities Cutting Dies - Standard Circle Large
Paypal   US $16.99
Nestabilities Cutting Dies- Classic Scalloped Circle Lg
Nestabilities Cutting Dies- Classic Scalloped Circle Lg
Paypal   US $16.99
Nestabilities Cutting Die - Big Scalloped Circles Large
Nestabilities Cutting Die - Big Scalloped Circles Large
Paypal   US $16.99
Creative Memories Custom Cutting System Circle Patterns
Creative Memories Custom Cutting System Circle Patterns
Paypal   US $8.99
NEW Nestabilities Cutting Die - Pinking Circles Small
NEW Nestabilities Cutting Die - Pinking Circles Small
Paypal   US $16.99
NMTB50 Circle Cutting Tool Boring Tool, Damaged
NMTB50 Circle Cutting Tool Boring Tool, Damaged
Paypal   US $9.99
NMTB50 Circle Cutting Tool Boring Bar 1
NMTB50 Circle Cutting Tool Boring Bar 1"
Paypal   US $9.99
Circle Cutting Tool NMTB50 Boring Bar 1.75
Circle Cutting Tool NMTB50 Boring Bar 1.75"
Paypal   US $9.99
Leichtung Oval & Circle Mat Cutting System
Leichtung Oval & Circle Mat Cutting System
Paypal   US $9.99
NEW Nestabilities Cutting Die - Pinking Circles Small
NEW Nestabilities Cutting Die - Pinking Circles Small
Paypal   US $16.99
Nestabilities Cutting Dies- Classic Scalloped Circle Lg
Nestabilities Cutting Dies- Classic Scalloped Circle Lg
Paypal   US $16.99
Nestabilities Cutting Dies - Standard Circle Large
Nestabilities Cutting Dies - Standard Circle Large
Paypal   US $16.99
Nestabilities Cutting Die - Big Scalloped Circles Small
Nestabilities Cutting Die - Big Scalloped Circles Small
Paypal   US $16.99
CRAFTSMAN CIRCLE CUTTING GUIDE 23413
CRAFTSMAN CIRCLE CUTTING GUIDE 23413
Paypal   US $9.99
Older Handmade Circle Y Cutting Saddle NEW NEVER USED!!
Older Handmade Circle Y Cutting Saddle NEW NEVER USED!!
Paypal   US $875.00
Creative Memories Custom Cutting System SET Circle Oval
Creative Memories Custom Cutting System SET Circle Oval
Paypal   US $49.99
FAMILY CIRCLE ROTARY CUTTING MAT & CUTTER - NEW
FAMILY CIRCLE ROTARY CUTTING MAT & CUTTER - NEW
Paypal   US $2.34
Silberschnitt/Bohle Strip & Circle Cutter & Cutting Mat
Silberschnitt/Bohle Strip & Circle Cutter & Cutting Mat
Paypal   US $81.99
CREATIVE MEMORIES CUTTING SYSTEM CIRCLES PATTERNS, NIP
CREATIVE MEMORIES CUTTING SYSTEM CIRCLES PATTERNS, NIP
Paypal   US $9.99
MILLER SPECTRUM PLASMA CIRCLE CUTTING GUIDE 195981
MILLER SPECTRUM PLASMA CIRCLE CUTTING GUIDE 195981
Paypal   US $127.77
Creative Memories LOT Cutting System Circles Ovals Mat
Creative Memories LOT Cutting System Circles Ovals Mat
Paypal   US $5.50
Nestabilities Cutting Die - Big Scalloped Circles Small
Nestabilities Cutting Die - Big Scalloped Circles Small
Paypal   US $16.99
Nestabilities Cutting Dies- Classic Scalloped Circle Lg
Nestabilities Cutting Dies- Classic Scalloped Circle Lg
Paypal   US $16.99
Nestabilities Cutting Die - Big Scalloped Circles Large
Nestabilities Cutting Die - Big Scalloped Circles Large
Paypal   US $16.99
Nestabilities Cutting Dies - Standard Circle Large
Nestabilities Cutting Dies - Standard Circle Large
Paypal   US $16.99
NEW Nestabilities Cutting Die - Pinking Circles Small
NEW Nestabilities Cutting Die - Pinking Circles Small
Paypal   US $16.99
16
16" CIRCLE Y Reining Cutting Team Penning SADDLE
Paypal   US $800.00
EK SUCCESS CIRCLE SCISSOR & CUTTING MAT & BLADES
EK SUCCESS CIRCLE SCISSOR & CUTTING MAT & BLADES
Paypal   US $8.00
Quality Circle Y Cutting Saddle
Quality Circle Y Cutting Saddle
Paypal   US $850.00
NEW GO! ACCUQUILT FABRIC CUTTING DIE CIRCLES 3 SHAPES
NEW GO! ACCUQUILT FABRIC CUTTING DIE CIRCLES 3 SHAPES
Paypal   US $9.99
Creative Memories Custom Cutting Circle Oval Mat Blades
Creative Memories Custom Cutting Circle Oval Mat Blades
Paypal   US $46.00
CREATIVE MEMORIES CUSTOM CUTTING SYSTEM CIRCLE PATTERNS
CREATIVE MEMORIES CUSTOM CUTTING SYSTEM CIRCLE PATTERNS
Paypal   US $4.25
Creative Memories Custom Cutting System Circle Patterns
Creative Memories Custom Cutting System Circle Patterns
Paypal   US $10.95
Creative Memories Custom Cutting System Jumbo Circle
Creative Memories Custom Cutting System Jumbo Circle
Paypal   US $10.95
Creative Memories Custom Cutting Circle Patterns
Creative Memories Custom Cutting Circle Patterns
Paypal   US $4.99
MILESCRAFT Circle Router and Edge Cutting Guide NEW
MILESCRAFT Circle Router and Edge Cutting Guide NEW
Paypal   US $38.99
Oval and Circle Mat Cutting System
Oval and Circle Mat Cutting System
Paypal   US $5.00
Jasper 200J Model 200 Circle Cutting Jig for Plunge Rou
Jasper 200J Model 200 Circle Cutting Jig for Plunge Rou
Paypal   US $32.20
CIRCLES cutting dies 4 piece cuttlebug NEW 37-1205 cut
CIRCLES cutting dies 4 piece cuttlebug NEW 37-1205 cut
Paypal   US $4.99
Milescraft 1203 TurnLock Router Circle and Edge Cutting
Milescraft 1203 TurnLock Router Circle and Edge Cutting
Paypal   US $27.79
Badge-A-Minit Cut-A-Circle for Cutting 2 1/4
Badge-A-Minit Cut-A-Circle for Cutting 2 1/4" Circles
Paypal   US $23.95
Circle cutting attachment for Victor torch
Circle cutting attachment for Victor torch
Paypal   US $25.00
GLASS CUTTING KIT WITH GLASS & CIRCLE CUTTER & BREAKER!
GLASS CUTTING KIT WITH GLASS & CIRCLE CUTTER & BREAKER!
Paypal   US $45.00
NEW Creative Memories CIRCLE CUTTING SYSTEM Patterns
NEW Creative Memories CIRCLE CUTTING SYSTEM Patterns
Paypal   US $9.99
CREATIVE MEMORIES CUTTING SYSTEM CIRCLES PATTERNS, NIP
CREATIVE MEMORIES CUTTING SYSTEM CIRCLES PATTERNS, NIP
Paypal   US $9.99
Sizzix Dies & Cutting Pads ~ Stars, Circles, Hearts ++
Sizzix Dies & Cutting Pads ~ Stars, Circles, Hearts ++
Paypal   US $29.99
Stampin Up COLUZZLE CUTTING TEMPLATES ~ CIRCLE & OVAL
Stampin Up COLUZZLE CUTTING TEMPLATES ~ CIRCLE & OVAL
Paypal   US $.99
Purox   Straight Line and Circle Cutting Guide, USA
Purox Straight Line and Circle Cutting Guide, USA
Paypal   US $39.99
Smith MC  Straight Line and Circle Cutting Guide, USA
Smith MC Straight Line and Circle Cutting Guide, USA
Paypal   US $39.99
Smith  SC  Straight Line and Circle Cutting Guide, USA
Smith SC Straight Line and Circle Cutting Guide, USA
Paypal   US $39.99
Oxweld   Straight Line and Circle Cutting Guide, USA
Oxweld Straight Line and Circle Cutting Guide, USA
Paypal   US $39.99
Airco 1369 Straight Line and Circle Cutting Guide, USA
Airco 1369 Straight Line and Circle Cutting Guide, USA
Paypal   US $39.99
Circle Scissors, Cutting Mat & Blades-Used Only Once!!
Circle Scissors, Cutting Mat & Blades-Used Only Once!!
Paypal   US $4.99
Creative Memories Custom Cutting Circle Patterns NEW
Creative Memories Custom Cutting Circle Patterns NEW
Paypal   US $9.99
Creative Memories Custom Cutting System Circles + BONUS
Creative Memories Custom Cutting System Circles + BONUS
Paypal   US $7.99
Creative Memories Circle cutting patterns NEW sealed
Creative Memories Circle cutting patterns NEW sealed
Paypal   US $9.99
Creative Memories Circle cutting patterns NEW sealed
Creative Memories Circle cutting patterns NEW sealed
Paypal   US $9.99
Accuquilt Go! Fabric Cutting Die Circle 2/3/5 IN. 55012
Accuquilt Go! Fabric Cutting Die Circle 2/3/5 IN. 55012
Paypal   US $.99
Olfa CMP-1 Adjustable Circle Cutting Cutter CMP1 New
Olfa CMP-1 Adjustable Circle Cutting Cutter CMP1 New
Paypal   US $11.99
CIRCLE Y CUTTING SADDLE + BILLY COOK  BREASTPLATE ~ NR
CIRCLE Y CUTTING SADDLE + BILLY COOK BREASTPLATE ~ NR
Paypal   US $749.00
Circle/Straight line cutting attach. for Victor torch.
Circle/Straight line cutting attach. for Victor torch.
Paypal   US $35.00
Milescraft 1203 TurnLock Router Circle and Edge Cutting
Milescraft 1203 TurnLock Router Circle and Edge Cutting
Paypal   US $33.48
*Tonic Shape Mate System CIRCLE CUTTING TEMPLATES
*Tonic Shape Mate System CIRCLE CUTTING TEMPLATES
Paypal   US $14.95
Circle Scissor Plus Cutting Tool - Pink
Circle Scissor Plus Cutting Tool - Pink
Paypal   US $28.99
Powered by phpBay Pro





Cutters Welding

Friday, June 4th, 2010

Cutters Welding
Cutters Welding

Clarifying the Myths About Plasma Cutters

For more than fifty years the plasma cutters have been used to cut metal since they provide several advantages over other metal cutting methods. But there are some myths related to the plasma cutters as many people have a misconception that plasma cutters are too expensive or too hard to learn. Conversely in realty, the plasma cutters are essential productivity enhancing tools.

It is true that Plasma Cutting systems are somewhat higher priced than some other cutting tools. But there is indeed a difference between price and cost. The plasma cutting systems are known for their high cutting speed and quality deliverance. Hence they provide productivity gain by saving operator's time and money. This is because the cutting machines do not require preheating of the work piece thus enabling the operators to complete jobs quickly. The main advantages of using plasma cutters include better quality cut with less dross and better edge quality. The labor intensive finishing operations are required only in a minimum level in the plasma cutting method.

The advancement in plasma cutting technology has thankfully outdated the false notion that plasma is only meant for cutting thin materials. Advances in the design and function of plasma cutting torches, consumables and Power Supply design have enabled the operators to get more cutting power and thicker cutting capacity even when the system size have shrunk. However it is true that earlier the handheld plasma cutters did not meet operator's expectations while cutting the thick metals. In addition, the plasma cutting machines provide some distinct advantages on thin materials like it causes less warping and only a smaller zone would be heat affected.

Many people purchase the plasma cutters for cutting Stainless Steel, aluminum or other non ferrous metals. There was a common disbelief that plasma cutting machines can only be used on such materials. But that is completely wrong since plasma can be effectively used to cut any electrically conductive metal and is one of the most popular means to cut Mild Steel. Plasma triumphs over oxyfuel cutting with its ability to cut stainless steel and aluminum. The cutters are even effective for cutting painted, dirty or rusted steel hence it can be used as a tool for heavy equipment repair, maintenance and other tasks.

Plasma systems are known for their versatile nature. They are capable of cutting, piercing and beveling metals of all types, shapes and sizes. With a change of the Plasma Cutting Torch or consumables, some plasma cutters can be switched between hand and automated cutting. They are widely used on robotic arms as beveling and also gouging tools. The systems are user friendly and produce less smoke and noise. The gouging operations for worn or cracked parts are perfectly done by the cutters than any other equipment. Thus the versatility of the plasma cutters enables the operators to finish both welding and gouging and save time and money. Moreover the plasma cutters are portable and light weighted and can be carried to any desired location.

About the Author

John is a Professional writer working with Everlastgenerators and he writes articles for Plasma Cutter. He written many articles like Welding Technology plasma cutting, Wire Feed Welder. Contact him at weldings.info@gmail.com. For more information visit our site http://www.everlastgenerators.com

Which of the following types of jobs are you willing to try?

1. Pediatrician (child Dr.)
2. film maker / director
3. forklift driver
4. welding
5. diamond cutter / jeweler
6. coal miner
7. jet pilot
8. politician
9. farming
10. sports referee
More than one answer is cool...=)

thanx~
Have a cool Yule everyone~

#s 2, 3, 6, 7 & 9.....!!

P30C 30Amp Plasma Cutter from R-Tech Welding

MIG TIG Plasma Cutter Arc Welding Cart w/ Tank Storage
MIG TIG Plasma Cutter Arc Welding Cart w/ Tank Storage
Paypal   US $57.99
NEW RSTAR CUT50D PLASMA CUTTER WELDING MACHINE 50 AMP
NEW RSTAR CUT50D PLASMA CUTTER WELDING MACHINE 50 AMP
Paypal   US $339.95
MIG TIG Plasma Cutter Arc Welding Cart w/ Tank Storage
MIG TIG Plasma Cutter Arc Welding Cart w/ Tank Storage
Paypal   US $39.99
Welding Cart W/ Tank Storage MIG TIG ARC Plasma Cutter
Welding Cart W/ Tank Storage MIG TIG ARC Plasma Cutter
Paypal   US $69.95
3/8
3/8" Double Ended Spot Weld Welding Cutter - NEW
Paypal   US $6.75
3/8
3/8" Double Ended Spot Weld Welding Cutter - NEW
Paypal   US $6.75
MIG TIG Plasma Arc Cutter Welding Cart w/ Tank Storage
MIG TIG Plasma Arc Cutter Welding Cart w/ Tank Storage
Paypal   US $67.00
New MIG TIG Plasma Arc Cutter Welding Cart Tank Storage
New MIG TIG Plasma Arc Cutter Welding Cart Tank Storage
Paypal   US $67.00
3/8
3/8" Double Ended Spot Weld Welding Cutter - NEW
Paypal   US $6.75
Dremel A=1/8
Dremel A=1/8" CYLINDER welding cutter burr bit metal A+
Paypal   US $6.99
3/8
3/8" Double Sided Rotary Spot Weld Cutter Welding Panel
Paypal   US $7.69
9
9" Mig Welding Pliers Grip Cutter
Paypal   US $19.99
WELDING CUTTER TIPS 1-101 0 1 2 QTY 3 free shipping NEW
WELDING CUTTER TIPS 1-101 0 1 2 QTY 3 free shipping NEW
Paypal   US $19.99
Provinol Seam Cutter Leister Forsthoff Heat Welding
Provinol Seam Cutter Leister Forsthoff Heat Welding
Paypal   US $69.99
L-tec pcm-54 plasma cutter welding welder metal working
L-tec pcm-54 plasma cutter welding welder metal working
   US $750.00
HIGH QUALITY FOOT PEDAL FOR WELDING/PLASMA CUTTER
HIGH QUALITY FOOT PEDAL FOR WELDING/PLASMA CUTTER
Paypal   US $114.99
HIGH QUALITY FOOT PEDAL FOR WELDING/PLASMA CUTTER
HIGH QUALITY FOOT PEDAL FOR WELDING/PLASMA CUTTER
Paypal   US $114.99
Welding Cart W/ Tank Storage MIG TIG ARC Plasma Cutter
Welding Cart W/ Tank Storage MIG TIG ARC Plasma Cutter
Paypal   US $69.95
CNC Laser Cutting Pay By The Hour Laser Cutter Welding
CNC Laser Cutting Pay By The Hour Laser Cutter Welding
Paypal   US $65.00
NEW WARNING PLASMA CUTTER HUMOR WELDING WELDER SIGN
NEW WARNING PLASMA CUTTER HUMOR WELDING WELDER SIGN
Paypal   US $12.95
HIGH QUALITY FOOT PEDAL FOR WELDING/PLASMA CUTTER
HIGH QUALITY FOOT PEDAL FOR WELDING/PLASMA CUTTER
Paypal   US $114.99
Welding Cart W/ Tank Storage MIG TIG ARC Plasma Cutter
Welding Cart W/ Tank Storage MIG TIG ARC Plasma Cutter
Paypal   US $72.95
Tig Welder Welding Machine Plasma Cutter Stick Arc
Tig Welder Welding Machine Plasma Cutter Stick Arc
Paypal   US $495.00
Tig Welder Welding Machine Plasma Cutter Stick Arc
Tig Welder Welding Machine Plasma Cutter Stick Arc
Paypal   US $495.00
Tig Welder Welding Machine Plasma Cutter Stick Arc
Tig Welder Welding Machine Plasma Cutter Stick Arc
Paypal   US $495.00
Tig Welder Welding Machine Plasma Cutter Stick Arc
Tig Welder Welding Machine Plasma Cutter Stick Arc
Paypal   US $495.00
Tig Welder Welding Machine Plasma Cutter Stick Arc
Tig Welder Welding Machine Plasma Cutter Stick Arc
Paypal   US $495.00
Tig Welder Welding Machine Plasma Cutter Stick Arc
Tig Welder Welding Machine Plasma Cutter Stick Arc
Paypal   US $495.00
Tig Welder Welding Machine Plasma Cutter Stick Arc
Tig Welder Welding Machine Plasma Cutter Stick Arc
Paypal   US $495.00
Tig Welder Welding Machine Plasma Cutter Stick Arc
Tig Welder Welding Machine Plasma Cutter Stick Arc
Paypal   US $495.00
Tig Welder Welding Machine Plasma Cutter Stick Arc
Tig Welder Welding Machine Plasma Cutter Stick Arc
Paypal   US $495.00
Tig Welder Welding Machine Plasma Cutter Stick Arc
Tig Welder Welding Machine Plasma Cutter Stick Arc
Paypal   US $495.00
Tig Welder Welding Machine Plasma Cutter Stick Arc
Tig Welder Welding Machine Plasma Cutter Stick Arc
Paypal   US $495.00
Tig Welder Welding Machine Plasma Cutter Stick Arc
Tig Welder Welding Machine Plasma Cutter Stick Arc
Paypal   US $495.00
Tig Welder Welding Machine Plasma Cutter Stick Arc
Tig Welder Welding Machine Plasma Cutter Stick Arc
Paypal   US $495.00
Tig Welder Welding Machine Plasma Cutter Stick Arc
Tig Welder Welding Machine Plasma Cutter Stick Arc
Paypal   US $495.00
Tig Welder Welding Machine Plasma Cutter Stick Arc
Tig Welder Welding Machine Plasma Cutter Stick Arc
Paypal   US $495.00
Tig Welder Welding Machine Plasma Cutter Stick Arc
Tig Welder Welding Machine Plasma Cutter Stick Arc
Paypal   US $495.00
Tig Welder Welding Machine Plasma Cutter Stick Arc
Tig Welder Welding Machine Plasma Cutter Stick Arc
Paypal   US $495.00
Tig Welder Welding Machine Plasma Cutter Stick Arc
Tig Welder Welding Machine Plasma Cutter Stick Arc
Paypal   US $495.00
ROTARY SPOT WELD CUTTER 3/8
ROTARY SPOT WELD CUTTER 3/8" WELDER'S TOOL WELDING AUTO
Paypal   US $7.98
3/8
3/8" Double Ended Spot Weld Welding Cutter Cut Bit Auto
Paypal   US $7.98
Welding Welder Arc Mig Tig Cutter Training Course CD
Welding Welder Arc Mig Tig Cutter Training Course CD
Paypal   US $8.95
Tig Welder Welding Machine Plasma Cutter Stick Arc
Tig Welder Welding Machine Plasma Cutter Stick Arc
Paypal   US $495.00
Tig Welder Welding Machine Plasma Cutter Stick Arc
Tig Welder Welding Machine Plasma Cutter Stick Arc
Paypal   US $495.00
NEW RSTAR CT520D 3 IN 1 PLASMA CUTTER WELDING MACHINE
NEW RSTAR CT520D 3 IN 1 PLASMA CUTTER WELDING MACHINE
Paypal   US $474.95
Tig Welder Welding Machine Plasma Cutter Stick Arc
Tig Welder Welding Machine Plasma Cutter Stick Arc
Paypal   US $495.00
NEW RSTAR CUT50D PLASMA CUTTER WELDING MACHINE 50 AMP
NEW RSTAR CUT50D PLASMA CUTTER WELDING MACHINE 50 AMP
Paypal   US $339.95
NEW RSTAR CT520D 3 IN 1 PLASMA CUTTER WELDING MACHINE
NEW RSTAR CT520D 3 IN 1 PLASMA CUTTER WELDING MACHINE
Paypal   US $474.95
NEW RSTAR CT520D 3 IN 1 PLASMA CUTTER WELDING MACHINE
NEW RSTAR CT520D 3 IN 1 PLASMA CUTTER WELDING MACHINE
Paypal   US $474.95
NEW RSTAR CUT50D PLASMA CUTTER WELDING MACHINE 50 AMP
NEW RSTAR CUT50D PLASMA CUTTER WELDING MACHINE 50 AMP
Paypal   US $339.95
NEW RSTAR CT520D 3 IN 1 PLASMA CUTTER WELDING MACHINE
NEW RSTAR CT520D 3 IN 1 PLASMA CUTTER WELDING MACHINE
Paypal   US $474.95
3/8
3/8" Double Ended Spot Weld Welding Cutter - NEW
Paypal   US $6.75
NEW RSTAR CUT50D PLASMA CUTTER WELDING MACHINE 50 AMP
NEW RSTAR CUT50D PLASMA CUTTER WELDING MACHINE 50 AMP
Paypal   US $339.95
NEW RSTAR CT520D 3 IN 1 PLASMA CUTTER WELDING MACHINE
NEW RSTAR CT520D 3 IN 1 PLASMA CUTTER WELDING MACHINE
Paypal   US $474.95
NEW RSTAR CUT50D PLASMA CUTTER WELDING MACHINE 50 AMP
NEW RSTAR CUT50D PLASMA CUTTER WELDING MACHINE 50 AMP
Paypal   US $339.95
NEW RSTAR CT520D 3 IN 1 PLASMA CUTTER WELDING MACHINE
NEW RSTAR CT520D 3 IN 1 PLASMA CUTTER WELDING MACHINE
Paypal   US $474.95
NEW RSTAR CUT50D PLASMA CUTTER WELDING MACHINE 50 AMP
NEW RSTAR CUT50D PLASMA CUTTER WELDING MACHINE 50 AMP
Paypal   US $339.95
Dive Diver SCUBA WELDER WELDING Salvage Torch Cutter CD
Dive Diver SCUBA WELDER WELDING Salvage Torch Cutter CD
Paypal   US $8.99
Welding Cart W/ Tank Storage MIG TIG ARC Plasma Cutter
Welding Cart W/ Tank Storage MIG TIG ARC Plasma Cutter
Paypal   US $72.95
Welding Cart W/ Tank Storage MIG TIG ARC Plasma Cutter
Welding Cart W/ Tank Storage MIG TIG ARC Plasma Cutter
Paypal   US $72.95
Welding Cart W/ Tank Storage MIG TIG ARC Plasma Cutter
Welding Cart W/ Tank Storage MIG TIG ARC Plasma Cutter
Paypal   US $69.95
Powered by phpBay Pro





Welders Cutting Torch

Saturday, May 29th, 2010

Welders Cutting Torch
Welders Cutting Torch

Gas Welding "101" - Details to Help You Become a Successful Gas Welder

Gas Welding is alive and well!
* If you want to create artistic projects, many people will choose gas welding exclusively.
* At some point, most arc welders will want to, or NEED to use gas welding. I'll help you get started. Then YOU need lots of practice!

Seriously, practice is CRITICAL for running great beads.
* If you're doing artistic stuff, you'll want it to LOOK great.
* Eye-hand coordination gets tougher because you're doing more multi-tasking then Arc Welding.
Being able to DIRECTLY be shown details about how to do special jobs like gas welding is the BEST way to get started. (By WATCHING some else gas weld).

Here's the "scoop" for this article:
1) I'll give you a brief introduction to the gas welding world...
2) Then I'll hit on some safety tips...
3) Next the equipment itself...
4) Getting started:
* The flame.
* Adjustments.
* Angles.
5) Filler rod, tacking, the puddle, problem solving.
6) Brazing Tips.

INTRO:
* Gas welding in this page refers to oxygen-Acetylene Welding of metals.
* Your are actually WELDING two pieces of metal together, wheras brazing doesn't melt the parent material, just the material used to join the pieces.
* The torch itself needs to be able to melt the metals being used: filler rod, & "parent metals".
* Having an oxygen-Acetylene Torch around enables you to not only WELD, but also to cut the materials, heat & bend materials, & loosen tight-fitting materials via heating.
* Safety is paramount! You are working with extremely hot & potentially explosive materials!

SAFETY STUFF:
SERIOUSLY gas welding can really be fun, interesting, & profitable!
BUT:
* The tuned gas flame can exceed 6,000 F.
* Un-protected eyes can be fatigued & permanently harmed in a short time.
* The acetylene tank could explode under certain conditions: dropping, in a fire, from an arc or torch flame penetrating the casing, etc.
* The oxygen tank starts with 2000 PSI & can literally go like a rocket if the top valve assembly breaks off.
* Hitting something already burning with the high pressure torch valve can really accelerate the fire.

So, be careful!

GETTING STARTED:

The Flame:
* Set the gas and oxygen pressures MUCH lower than for cutting.
* Some gas setting charts call for the 02 & gas pressures to be the same as the tip size being used: tip size 1 = 1 PSI for gas & O2.
* Tip size 5 = 5 PSI for gas & O2, etc.
* I simplify things even farther! I just set both pressures at 10 PSI then crack the valves open at the Torch Handle to where I need them to be. Just start EASY & work them up to the capabilities of the tip. (or just do it as above).
* Also, tip sizes vary for the size metal being welded: Tip size 1 = 1/16" metal and tip size 5 = 1/4" as examples.
* It really isn't hard to figure out if the tip your using is too small or too big for the job. (Too small won't get everything hot enough, & too large will tend to blow everything away).
* Crack open the gas & light it right away.
* Crank up the gas till it separates from the tip then back it off.
* Hit the O2 until the Blue Flame first gets short & bright. This is a "neutral flame", used for most jobs.

Note that the Torch Tip & the filler rod should be about at a 45 degree angle.
*Too steep can make the penetration too deep & not pre-heat / too shallow can cause too little penetration.

Let's do it:
* Starting out, it can give you good practice to just put the flame on metal without a filler rod. This helps you get used to the process without worrying about the filler rod too.
* Heat the metal till there's a puddle, then begin moving the flame to create a bead.
* Get the blue part of the flame nearly touching the metal.
* Move in a circular or semi-circular fashion to make it into a bead.
* Aim the flame in the direction you're trying to make the bead. (forehand welding).
* Don't get ahead of the bead or it can make it not hot enough at the puddle.
* Do this for a few times before using a filler rod.

Introduce a filler rod: (usually the same diameter as the pieces that are being welded).
* start the same way as above and keep the rod at a 45 degree angle also.
* Dip the rod in the puddle frequently, but try not to heat the rod with the flame. (heat the puddle, not the rod).
* Practice running straight beads then work up to following curved paths. (some schools have you write your name with a gas welding bead).

THEN PRACTICE till you can run decent looking beads.

Note that you should be tacking pieces together at least at both ends of where you're welding, to prevent moving of the gap.

Problem solving:
* Your flame is fluctuating: gas pressure or supply may be low.
* Popping sound: Hot tip, plugged tip, pressure too high.
* Flame stops: 02 pressure high.
* Whistling noise & the flame backs up into the torch: (backfire), 02 or gas too low, the tip is clogged or dirty, or the tip touched the puddle.

BRAZING:
* Many things are similar about gas welding and brazing: but remember that with brazing you aren't melting the parent metal, just the brazing material (such as brass).
* The brass and the parent metal MUST be clean and hot enough for there to be a good joint. (Use flux! In a can, or coated rods).
* Think of soldering, if you don't get everything hot enough, it might come apart (or not be a good electrical connection).

Now GET BUSY PRACTICING!

This was a just a BRIEF description of the gas welding process.

Good luck to all you ladies & gents!

About the Author

I started working as a Journey-level welder for Weyerheauser Timber Company more than 20 years ago. That was the same year that I became a certified welder in Washington State.
I weld today because it's cool & interesting! If you can DREAM it, you can probably WELD it!

My website: http://www.arc-welding-and-beyond.com

 

The purpose of my website is to educate the beginning welder in ALL RELATED skill areas of welding: running great beads, designing, preparing, layout, finishing, & troubleshooting problems.

"Welding is more than just running beads!"

i found a 1977 mgb convertible in good shape dirt cheap. i have a small block ford engine that i am not using?

anyone have any experience doing a v-8 swap? i am a decent mechanic and can borrow any tool i might need,welder,torch. i saw this car and wondered if it was something that could be done without spending a ton of money. just trying to get some input on how hard it would be because i know 0 about these cars. can it be done without any major cutting or modifications?

Ford swap article:
http://www.britishv8.org/Articles/Ford-5L-EFI-Installation.htm

Conversion parts:
http://www.aluminumv8.com/catalogpages/altigspark.htm

Henrob 2000 Welding and Cutting Torch

5  Victor Style Welders cutting torch Tips #3-1-101 NEW
5 Victor Style Welders cutting torch Tips #3-1-101 NEW
Paypal   US $20.00
30+ Torch Cutting Arc Metal WELDING WELDER Pubs on CD
30+ Torch Cutting Arc Metal WELDING WELDER Pubs on CD
Paypal   US $14.99
5ea Victor Style Welders Cutting Torch Tips NIB 4-1-101
5ea Victor Style Welders Cutting Torch Tips NIB 4-1-101
Paypal   US $19.99
5ea Victor Style Welders Cutting Torch Tips NIB 3-1-101
5ea Victor Style Welders Cutting Torch Tips NIB 3-1-101
Paypal   US $19.99
OXY ACETYLENE WELDER KIT  WELDING TORCH HEATING CUTTING
OXY ACETYLENE WELDER KIT WELDING TORCH HEATING CUTTING
Paypal   US $37.88
OXY ACETYLENE WELDER KIT  WELDING TORCH HEATING CUTTING
OXY ACETYLENE WELDER KIT WELDING TORCH HEATING CUTTING
Paypal   US $37.88
OXY ACETYLENE WELDER KIT  WELDING TORCH HEATING CUTTING
OXY ACETYLENE WELDER KIT WELDING TORCH HEATING CUTTING
Paypal   US $37.88
OXY ACETYLENE WELDER KIT  WELDING TORCH HEATING CUTTING
OXY ACETYLENE WELDER KIT WELDING TORCH HEATING CUTTING
Paypal   US $37.88
OXY ACETYLENE WELDER KIT  WELDING TORCH HEATING CUTTING
OXY ACETYLENE WELDER KIT WELDING TORCH HEATING CUTTING
Paypal   US $37.88
OXY ACETYLENE WELDER KIT  WELDING TORCH HEATING CUTTING
OXY ACETYLENE WELDER KIT WELDING TORCH HEATING CUTTING
Paypal   US $37.88
OXY ACETYLENE WELDER KIT  WELDING TORCH HEATING CUTTING
OXY ACETYLENE WELDER KIT WELDING TORCH HEATING CUTTING
Paypal   US $37.88
OXY ACETYLENE WELDER KIT  WELDING TORCH HEATING CUTTING
OXY ACETYLENE WELDER KIT WELDING TORCH HEATING CUTTING
Paypal   US $37.88
OXY ACETYLENE WELDER KIT  WELDING TORCH HEATING CUTTING
OXY ACETYLENE WELDER KIT WELDING TORCH HEATING CUTTING
Paypal   US $37.88
OXY ACETYLENE WELDER KIT  WELDING TORCH HEATING CUTTING
OXY ACETYLENE WELDER KIT WELDING TORCH HEATING CUTTING
Paypal   US $37.88
OXY ACETYLENE WELDER KIT  WELDING TORCH HEATING CUTTING
OXY ACETYLENE WELDER KIT WELDING TORCH HEATING CUTTING
Paypal   US $37.88
OXY ACETYLENE WELDER KIT  WELDING TORCH HEATING CUTTING
OXY ACETYLENE WELDER KIT WELDING TORCH HEATING CUTTING
Paypal   US $37.88
OXY ACETYLENE WELDER KIT  WELDING TORCH HEATING CUTTING
OXY ACETYLENE WELDER KIT WELDING TORCH HEATING CUTTING
Paypal   US $37.88
OXY ACETYLENE WELDER KIT  WELDING TORCH HEATING CUTTING
OXY ACETYLENE WELDER KIT WELDING TORCH HEATING CUTTING
Paypal   US $37.88
OXY ACETYLENE WELDER KIT  WELDING TORCH HEATING CUTTING
OXY ACETYLENE WELDER KIT WELDING TORCH HEATING CUTTING
Paypal   US $37.88
OXY ACETYLENE WELDER KIT  WELDING TORCH HEATING CUTTING
OXY ACETYLENE WELDER KIT WELDING TORCH HEATING CUTTING
Paypal   US $37.88
Victor Style Welders cutting torch Tips #3-1-101 25 pcs
Victor Style Welders cutting torch Tips #3-1-101 25 pcs
Paypal   US $145.00
OXY ACETYLENE WELDER KIT  WELDING TORCH HEATING CUTTING
OXY ACETYLENE WELDER KIT WELDING TORCH HEATING CUTTING
Paypal   US $37.88
OXY ACETYLENE WELDER KIT  WELDING TORCH HEATING CUTTING
OXY ACETYLENE WELDER KIT WELDING TORCH HEATING CUTTING
Paypal   US $37.88
5ea Victor Style Welders Cutting Torch Tips NIB   0-GPN
5ea Victor Style Welders Cutting Torch Tips NIB 0-GPN
Paypal   US $19.99
OXY ACETYLENE WELDER KIT  WELDING TORCH HEATING CUTTING
OXY ACETYLENE WELDER KIT WELDING TORCH HEATING CUTTING
Paypal   US $37.88
OXY ACETYLENE WELDER KIT  WELDING TORCH HEATING CUTTING
OXY ACETYLENE WELDER KIT WELDING TORCH HEATING CUTTING
Paypal   US $37.88
OXY ACETYLENE WELDER GAS CUTTING OUTFIT TORCH SET KIT
OXY ACETYLENE WELDER GAS CUTTING OUTFIT TORCH SET KIT
Paypal   US $149.99
OXY ACETYLENE WELDER KIT  WELDING TORCH HEATING CUTTING
OXY ACETYLENE WELDER KIT WELDING TORCH HEATING CUTTING
Paypal   US $37.88
OXY ACETYLENE WELDER KIT  WELDING TORCH HEATING CUTTING
OXY ACETYLENE WELDER KIT WELDING TORCH HEATING CUTTING
Paypal   US $37.88
5  Victor Style Welders cutting torch Tips #3-1-101 NEW
5 Victor Style Welders cutting torch Tips #3-1-101 NEW
Paypal   US $25.00
OXY ACETYLENE WELDER KIT  WELDING TORCH HEATING CUTTING
OXY ACETYLENE WELDER KIT WELDING TORCH HEATING CUTTING
Paypal   US $37.88
OXY ACETYLENE WELDER KIT  WELDING TORCH HEATING CUTTING
OXY ACETYLENE WELDER KIT WELDING TORCH HEATING CUTTING
Paypal   US $37.88
Harris OEM 6290 ON Machine Torch Cutting Tip New Welder
Harris OEM 6290 ON Machine Torch Cutting Tip New Welder
Paypal   US $29.99
WELDING WALL CLOCK of cutting torch welder with helmet
WELDING WALL CLOCK of cutting torch welder with helmet
Paypal   US $16.99
WELDING DESK CLOCK of cutting torch welder with helmet
WELDING DESK CLOCK of cutting torch welder with helmet
Paypal   US $16.99
S-S Company Metalmaster Welder's Cutting Torch Vintage
S-S Company Metalmaster Welder's Cutting Torch Vintage
Paypal   US $24.99
VINTAGE 70s WELDER BUCKLE **CUTTING TORCH** TIP VICTOR
VINTAGE 70s WELDER BUCKLE **CUTTING TORCH** TIP VICTOR
Paypal   US $35.00
WELDER'S CUTTING TORCH
WELDER'S CUTTING TORCH
Paypal   US $65.00
Linde Track Cutting Track Torch Welder
Linde Track Cutting Track Torch Welder
Paypal   US $499.00
30+ Torch Cutting Arc Metal WELDING WELDER Pubs on CD
30+ Torch Cutting Arc Metal WELDING WELDER Pubs on CD
Paypal   US $14.99
Powered by phpBay Pro





Welding Helmets

Tuesday, May 18th, 2010

Welding Helmets
Welding Helmets

Welding Helmets - Do You Really Know Which Helmet You Want?

There are many types of welding helmets, and many prices!

First: Chuck that hand-held helmet as soon as you can!
Second: At LEAST get a $20 basic black flip-lens type.
Third: For about $35 you can get a large lens flip-up regular helmet. (Hobart #770003, via Amazon.com).
Fourth: If you've got $60 get a basic auto-Darkening Helmet from weldinghelmetstore.com, or wherever else.
Fifth: If you can afford to, shop around at a local welding shop to see if there's any that you can get. If not go to Craigslist, or similar place. (Example: $65 late model "auto" in Longbeach, Ca.)

Helmets can be anywhere from about $20 to $300 PLUS!

But Before You Buy:

READ THESE DETAILS & SUGGESTIONS:

There's more to consider that just COSTS:
1) Lens type...
2) Variable or fixed shade...
3) Switching Times from light to dark (& back)...
4) How it's powered...
5) Safety...does it meet the latest standards?

*Lens Type: Auto-darkening or Regular Lens:

Auto-darkening:
1) No need to flip the viewing lid or the whole helmet.
2) If you're working in tight places, you have more room to work.
3) You can set up the work-pieces & the rod (or wire gun), easier without flipping the hood up & down.
4) It's easier on your neck, without all the flipping.
5) You can SEE your work-piece setup, but still have protection once you strike the arc.
6) They are powered by battery &/or solar.

Regular lens:
1) They are cheaper & OK for anyone just beginning.
2) When you're ready to do a lot of welding, you will likely want to change to auto-darkening.
3) More chances of getting flash-burns & having your work-pieces move while flipping.
4) Most have a much smaller viewing area.

Variable or Fixed Shade:
1) Fixed shade: If you'll be welding at similar amperages & welding types, a fixed shade of a #10 would work for most of us.
2) Variable Shade: If you will be doing very much higher AMP welding (above 200 AMPS), then you'll want the shade to vary to #12 or more, depending on what your doing.
3) Switching times: (light to dark, etc), to help protect your eyes).
* They range from about 1/3600th of a second to 1/16000th. The faster they are the more cost. Eye fatigue can result from the slower speeds.

How they're powered:

* Battery: Lithium for longer lasting / Or alkaline batteries for cheaper replacements.

Safety:

*ANZI Z87 - 2003 or newer are the safer ones. Older ones may fatigue your eyes more, due to how fast/slow they change shades/darkness.

About the Author

I started working as a Journey-level welder for Weyerheauser Timber Company more than 20 years ago. That was the same year that I became a certified welder in Washington State.
I weld today because it's cool & interesting! If you can DREAM it, you can probably WELD it!

My website: http://www.arc-welding-and-beyond.com

 

The purpose of my website is to educate the beginning welder in ALL RELATED skill areas of welding: running great beads, designing, preparing, layout, finishing, & troubleshooting problems.

"Welding is more than just running beads!"

Yes, an amp & volt gage inside a Welding Helmet ro read the weld, Any help?

Yes I enjoy Tig Welding and watching the weld in detail. I would like to add the amp and volt gages inside the helmet to read the weld and eventually sence the correctness of the weld. I am thinking of a bar or line type of gage so I can watch the weld and sence where the line is and watch the weld. I need to know what type of gage would be best to try: rippeyrip@yahoo.com

that is not going to make you a welder trust me PRACTICE............ also try a lower # on your lense I use a #9

Jackson Welding Helmets

Flames AUTO DARKENING WELDING HELMET Arc TIG MIG ANSI
Flames AUTO DARKENING WELDING HELMET Arc TIG MIG ANSI
Paypal   US $48.99
Accu-Strike Welding Helmet with Box and Gold Lens
Accu-Strike Welding Helmet with Box and Gold Lens
Paypal   US $59.00
FIBRE-METAL #990-3C WELDING HELMET-USED-NICE CONDITION!
FIBRE-METAL #990-3C WELDING HELMET-USED-NICE CONDITION!
Paypal   US $5.50
WELDING HELMET AUTO DARKENING MIG TIG ARC GAS welder 1
WELDING HELMET AUTO DARKENING MIG TIG ARC GAS welder 1
Paypal   US $20.50
AUTO DARKENING WELDING HELMET SOLAR ARK MIG MAG MASK 07
AUTO DARKENING WELDING HELMET SOLAR ARK MIG MAG MASK 07
Paypal   US $49.99
Flaming Eagle AUTO DARKENING WELDING HELMET Arc TIG MIG
Flaming Eagle AUTO DARKENING WELDING HELMET Arc TIG MIG
Paypal   US $49.99
Auto Fast Darkening Welding Helmet Welder Tig Mig Arc
Auto Fast Darkening Welding Helmet Welder Tig Mig Arc
Paypal   US $34.95
Hood Auto Darkening Welding Helmet  carbon Fiber Black1
Hood Auto Darkening Welding Helmet carbon Fiber Black1
Paypal   US $49.99
AUTO DARKENING RED FLAME WELDING HELMET solar dark new
AUTO DARKENING RED FLAME WELDING HELMET solar dark new
Paypal   US $49.99
WELDING HELMET with FLIP UP LENS New goggle weld
WELDING HELMET with FLIP UP LENS New goggle weld
Paypal   US $19.99
Solar Powered AUTO DARKENING WELDING HELMET weld goggle
Solar Powered AUTO DARKENING WELDING HELMET weld goggle
Paypal   US $49.99
Qty2: Welders Welding Helmet:Use with Mig or Tig Welder
Qty2: Welders Welding Helmet:Use with Mig or Tig Welder
Paypal   US $9.99
AUTO DARKEN DARKENING SOLAR WELDING HELMET MASK HOOD
AUTO DARKEN DARKENING SOLAR WELDING HELMET MASK HOOD
Paypal   US $52.95
SOLAR AUTO DARKENING WELDING GRINDING HELMET MASK MIG G
SOLAR AUTO DARKENING WELDING GRINDING HELMET MASK MIG G
Paypal   US $57.95
new Certified ANSI CE Welding Helmet Carbon Fiber Black
new Certified ANSI CE Welding Helmet Carbon Fiber Black
Paypal   US $49.99
WELDING HELMET AUTO DARKENING MIG TIG ARC GAS welder 1
WELDING HELMET AUTO DARKENING MIG TIG ARC GAS welder 1
Paypal   US $21.71
Qty2: Welders Welding Helmet:Use with Mig or Tig Welder
Qty2: Welders Welding Helmet:Use with Mig or Tig Welder
Paypal   US $19.99
Auto darkening Welding mask Helmet Solar Cell mig 02
Auto darkening Welding mask Helmet Solar Cell mig 02
Paypal   US $32.99
10 RADNOR 2
10 RADNOR 2" X 4-1/4" WELDING HELMET LENSES NEW
Paypal   US $9.99
WELDING HELMET AUTO DARKENING MIG TIG ARC GAS welder 1
WELDING HELMET AUTO DARKENING MIG TIG ARC GAS welder 1
Paypal   US $18.00
WELDING HELMET Great for body shop or wire feed welder
WELDING HELMET Great for body shop or wire feed welder
Paypal   US $.99
Hood Auto Darkening Welding Helmet  carbon Fiber Red
Hood Auto Darkening Welding Helmet carbon Fiber Red
Paypal   US $49.99
Qty2: Welders Welding Helmet:Use with Mig or Tig Welder
Qty2: Welders Welding Helmet:Use with Mig or Tig Welder
Paypal   US $9.99
Lincoln Electric Welding Helmet Solar Powered Auto Dark
Lincoln Electric Welding Helmet Solar Powered Auto Dark
Paypal   US $92.00
SOLAR AUTO DARKENING WELDING HELMET HOOD ARC MIG METAL
SOLAR AUTO DARKENING WELDING HELMET HOOD ARC MIG METAL
Paypal   US $67.99
SOLAR POWER AUTO DARKENING WELDING HELMET ARC/TIG/MIG
SOLAR POWER AUTO DARKENING WELDING HELMET ARC/TIG/MIG
Paypal   US $57.99
AUTO DARKENING WELDING HELMET ARC/MIG AMERICAN EAGLE
AUTO DARKENING WELDING HELMET ARC/MIG AMERICAN EAGLE
Paypal   US $57.99
SOLAR AUTO DARKENING WELDING GRINDING HELMET MASK MIG G
SOLAR AUTO DARKENING WELDING GRINDING HELMET MASK MIG G
Paypal   US $57.95
SOLAR AUTO DARKENING WELDING GRINDING HELMET MASK HOOD
SOLAR AUTO DARKENING WELDING GRINDING HELMET MASK HOOD
Paypal   US $57.95
3M SPEEDGLAS SL Welding Helmet - Super Light, High-end
3M SPEEDGLAS SL Welding Helmet - Super Light, High-end
Paypal   US $169.00
Jackson Halo-X Welding Helmet with NexGen lense NEW
Jackson Halo-X Welding Helmet with NexGen lense NEW
Paypal   US $154.49
WELDING HELMET AUTO DARKENING MIG TIG ARC GAS welder
WELDING HELMET AUTO DARKENING MIG TIG ARC GAS welder
Paypal   US $17.18
AUTO DARKENING WELDING HELMET Arc TIG MIG Welder-ANSI
AUTO DARKENING WELDING HELMET Arc TIG MIG Welder-ANSI
Paypal   US $39.49
SOLAR AUTO DARKENING WELDING GRINDING HELMET MASK MIG G
SOLAR AUTO DARKENING WELDING GRINDING HELMET MASK MIG G
Paypal   US $57.95
New Solar Power Auto Darkening Welding Helmet ANSI 1814
New Solar Power Auto Darkening Welding Helmet ANSI 1814
Paypal   US $44.99
New Speedway Series Auto Darkening Welding Helmet 4597
New Speedway Series Auto Darkening Welding Helmet 4597
Paypal   US $37.99
AUTO DARK WELDING HELMET MASK WITH SOLAR POWER CELL 1
AUTO DARK WELDING HELMET MASK WITH SOLAR POWER CELL 1
Paypal   US $34.99
Harley Davidson Welding Helmet
Harley Davidson Welding Helmet
Paypal   US $70.00
Solar Auto Darkening Welder Welding Helmet Tig Mig Arc
Solar Auto Darkening Welder Welding Helmet Tig Mig Arc
Paypal   US $49.99
Brand New Neiko Welding Helmet Lift Front Shade #11
Brand New Neiko Welding Helmet Lift Front Shade #11
Paypal   US $13.99
AUTO DARKEN DARKENING SOLAR WELDING HELMET MASK HOOD
AUTO DARKEN DARKENING SOLAR WELDING HELMET MASK HOOD
Paypal   US $52.95
WELDING HELMET AUTO DARKENING MIG TIG ARC GAS welder
WELDING HELMET AUTO DARKENING MIG TIG ARC GAS welder
Paypal   US $16.01
Welding helmet,auto darkening lens w/American Eagle
Welding helmet,auto darkening lens w/American Eagle
Paypal   US $129.99
BLUE FLAME DESIGN AUTO DARKENING WELDING HELMET AS IS
BLUE FLAME DESIGN AUTO DARKENING WELDING HELMET AS IS
Paypal   US $9.99
Qty2: Welders Welding Helmet:Use with Mig or Tig Welder
Qty2: Welders Welding Helmet:Use with Mig or Tig Welder
Paypal   US $9.90
Solar AutoDark lcd Welding Mask Hood Helmet Tig Mig Arc
Solar AutoDark lcd Welding Mask Hood Helmet Tig Mig Arc
Paypal   US $49.99
AUTO DARK WELDING HELMET MASK W/ SOLAR POWEr Cell mig
AUTO DARK WELDING HELMET MASK W/ SOLAR POWEr Cell mig
Paypal   US $39.99
AUTO-DARKENING WELDING HELMET MIG/TIG WELDING TADD
AUTO-DARKENING WELDING HELMET MIG/TIG WELDING TADD
Paypal   US $9.99
FLAMING SKULL WELDING HELMET TADD
FLAMING SKULL WELDING HELMET TADD
Paypal   US $9.99
AUTO DARKENING WELDING HELMET
AUTO DARKENING WELDING HELMET
Paypal   US $9.99
BLUE FLAME DESIGN AUTO DARKENING WELDING HELMET
BLUE FLAME DESIGN AUTO DARKENING WELDING HELMET
Paypal   US $9.99
Solar Auto Dark Adj Welding Mask Helmet MIG TIG ARC XDH
Solar Auto Dark Adj Welding Mask Helmet MIG TIG ARC XDH
Paypal   US $27.40
Solar Auto Dark Blue Welding Mask Helmet MIG TIG ARC 3
Solar Auto Dark Blue Welding Mask Helmet MIG TIG ARC 3
Paypal   US $31.06
Solar AUTO DARKENING WELDING HELMET Arc TIG MIG Welder
Solar AUTO DARKENING WELDING HELMET Arc TIG MIG Welder
Paypal   US $39.99
Hobart Welding Helmet
Hobart Welding Helmet
Paypal   US $40.00
Solar AutoDark Lens Welding Helmet Tig Mig Arc Grinding
Solar AutoDark Lens Welding Helmet Tig Mig Arc Grinding
Paypal   US $54.99
WELDING HELMET AUTO DARKENING MIG TIG ARC GAS welder 1
WELDING HELMET AUTO DARKENING MIG TIG ARC GAS welder 1
Paypal   US $20.50
Auto Darkening Solar Welding Helmet Kit Gloves Clamps
Auto Darkening Solar Welding Helmet Kit Gloves Clamps
Paypal   US $199.99
Mexican Flag Welding Helmet with Auto Lens - NEW
Mexican Flag Welding Helmet with Auto Lens - NEW
Paypal   US $15.00
Mexican Flag Welding Helmet with Auto Lens - NEW
Mexican Flag Welding Helmet with Auto Lens - NEW
Paypal   US $15.00
HOODLUM Red Flame Skull Welding Helmet Auto Lens - NEW
HOODLUM Red Flame Skull Welding Helmet Auto Lens - NEW
Paypal   US $49.99
HOODLUM Red Flame Skull Welding Helmet Auto Lens - NEW
HOODLUM Red Flame Skull Welding Helmet Auto Lens - NEW
Paypal   US $49.99
HOODLUM Lava Skull Welding Helmet Auto Lens - NEW
HOODLUM Lava Skull Welding Helmet Auto Lens - NEW
Paypal   US $49.99
HOODLUM Lava Skull Welding Helmet Auto Lens - NEW
HOODLUM Lava Skull Welding Helmet Auto Lens - NEW
Paypal   US $49.99
2 North 8400 Series Welding Helmets with Resperators
2 North 8400 Series Welding Helmets with Resperators
Paypal   US $200.00
Carbon Fiber Welding Grinding Helmet w/ Auto Lens - NEW
Carbon Fiber Welding Grinding Helmet w/ Auto Lens - NEW
Paypal   US $49.99
Powered by phpBay Pro





Hobart Airforce

Friday, May 14th, 2010

Hobart Airforce
Hobart Airforce

Does a Plasma Cutter use air from a compressor to cut, or is a Welding Gas required?

Hobart Plasma Cutter - Airforce 400

It does not reqire welding gas required

Torchmate 2x2 and Hobart Airforce 700i

Hobart AirForce 250CI Plasma Cutter 12 Amps
Hobart AirForce 250CI Plasma Cutter 12 Amps
Paypal   US $799.99
Hobart AirForce 625 & ICE-40C Torch owners manual
Hobart AirForce 625 & ICE-40C Torch owners manual
Paypal   US $14.00
Hobart Air Force 500i Plasma Cutter with MVP
Hobart Air Force 500i Plasma Cutter with MVP
Paypal   US $1,299.99
Hobart Air Force 700i Plasma Cutter -New
Hobart Air Force 700i Plasma Cutter -New
Paypal   US $1,499.99
Hobart AirForce 750 owners manual
Hobart AirForce 750 owners manual
Paypal   US $11.00
Hobart 770497 Cap,Swirl Ring & O-Ring Kit for Airforce
Hobart 770497 Cap,Swirl Ring & O-Ring Kit for Airforce
Paypal   US $21.25
Hobart 770497 Cup Swirl Kit AirForce 250Ci Plasma Torch
Hobart 770497 Cup Swirl Kit AirForce 250Ci Plasma Torch
Paypal   US $16.80
Hobart Airforce 500534 250ci Light Weight Plasma Cutter
Hobart Airforce 500534 250ci Light Weight Plasma Cutter
Paypal   US $871.44
Hobart Air Force 500i Plasma Cutter with MVP
Hobart Air Force 500i Plasma Cutter with MVP
Paypal   US $1,299.99
Hobart Air Force 700i Plasma Cutter -New
Hobart Air Force 700i Plasma Cutter -New
Paypal   US $1,499.99
hobart airforce 500i plasma cutter
hobart airforce 500i plasma cutter
Paypal   US $1,000.00
barnd new hobart plasma cutter airforce 500i
barnd new hobart plasma cutter airforce 500i
Paypal   US $1,000.00
Hobart AirForce 250CI Plasma Cutter 12 Amps
Hobart AirForce 250CI Plasma Cutter 12 Amps
Paypal   US $799.99
HOBART AIRFORCE 625 PLASMA CUTTER
HOBART AIRFORCE 625 PLASMA CUTTER
Paypal   US $899.00
Powered by phpBay Pro






wordpress visitor counter